Відео

❤

I change a fuse and I work the next day no longer k. will it be what happens?

This solved my problem. The fuse was blown, went to Auto Zone and got a new one. Working as it should, thanks!

What do you mean when you say the ready light?

Cleaned my condenser and radiator. Removed the fan (moved back) and made a made shift wand yo attract to my garden hose out of copper pipe. My AC blows cold again after washing all the road dirt and grime

It would help to know who's rebuild kit NOT to buy !!

Was it not blowing at all or was it blowing hot?

💙💙💙🙏🙏🙏💙💙💙

The buzz sound is funny 😂

Oh my lord it worked!! Happened today when I first tried using the AC this year. Luckily I did a Google search when I got home and found this video! Liked, and Subscribed! Note,.. I was using the AC at times to heat the vehicle during the winter months and got heat! So I'm assuming that fuse is just for the AC!? IDK, but my quick test in the garage, it was blowing cold again! Knock on wood it continues working next time I drive it.

What a waste of time. Your parents must be so proud.

You forgot one small detail! Lining the notches up in carb body with the 4 holes at the bottom of the main jet. This is very important.

I need to get my 76 custom running. It’s a decent build

I’m using the rod, but I’m not getting any traction.

Booooooo

Fixed it to get it smoged and now its staying on 😭🤣

I would advise to pull the fuse out and check for any burnt signs and check continuity with a cheap volt meter. The other day I pulled one out and it was burnt on the side and you would not have known if you didn't pull it all the way out.

Is it normal to press many fusibles because many are at the top?

Just saved my week 😂 Good shit my guy

This is exactly what’s wrong with mine, can i reattach with super glue?

I have that washer 20 plus old-my agitator came off during cycle. Can I drain without it in place?

Thanks. I just changed mine. Took like for minutes because I took my time. Lol. Easr than changing the air filter😁

I got a free 68 Daysailer. It had hull damage in two places. It already has the mast cut and a tabernacle installed. Good sails, too; not the originals.

The bottom gets worn down and it turns into a suckerfish.

My goodness you are amazing for filming this for us! Thank you so much!

Basura de video

TY so very much for this video!

Interesting video. By the time those bearings go bad, I just replace the brush roll & belt and it works like new again. I also blow the motor out with the air compressor

Thank you, I wonder what size is the nut or thing you have turn. Thinking I could use a power tool for it...

The whole dyna family, fxrs and sportys have the same front ends from what I've seen so far..

Love it! Im redoing my 73 as we speak!

Thankyou after it took me 3hrs trying to figure it out... Problem solve...Ur vid. Cheers from aus/in brizzy

Wife car sometimes won't go over 60 but no engine light or nothing what should I check

My '96 Jeep Grand Cherokee 4.0 shifted down from overdrive coming home last night and got worse, not shifting down into 1st gear. Then this morning I took it for a drive like I normally do starting out and it had very hard times shifting past 2nd gear but would. Then after a few more test drives it would not even shift into R, D, 2 or 1!!! The transmission just doesn't do anything besides park and Neutral. Any ideas? Thank you.

It works car starts with no problem!!!

More or less have the same washer. Leaking from somewhere. Took some blanking plates off the back and looked in. Cant tell where it is. Supposedly you're able to put like a paint scraper in between the upper assembly and lower assembly and the whole top is supposed to hinge up. However that didn't work for mine. Thinking theres two screws underneath or something holding the front panel on. Cant mess with it anymore. Need a pair of channel locks to get the inlet hoses off. Then I can look underneath.

Cant see shit! Hahaha

Are you kidding ?! Didn't you watch this before you posted it ? How the hell did you hear it? And why did you post it anyway ? If you want to do this, buy a microphone, so we can hear what the hell you're saying !

😎👍😎

I know this video is pretty old, but i wanted to thank you for posting it. I had the exact same issue and the exact same line broke. Looks like the PO tried to repair it and glued the line in, and it just broke further down. Still plenty of line so i just snugged it into the cone and its working fine. I think youre on to something with replacing it with a 90, cause theres clearly some kind of tension on it. Ill get around to it someday, but irs working great for now!

thank you but holy crap man with the videoing

Гайку приварить, что не судьба было?

Nice central system!

Water in carboratetor.

GREAT job! very impressive transformation.Working on one of my three Ironheads right now having a blast

Well there's 6 mins of my life i wont get back

Thanks mate from 🇦🇺. Was much needed to know.

Man thank you i put a throttle body spacer on my jeep grand cherokee 2000 eith the 4.0 and it added slack this save me alot of stress and money i was already about to try transmission solenoid .

Chaos!!!!!

ir0nheads rule!!! 🤘😎🤘